? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 1 of 10 sat800 ac input 60v dual photo-transistor optocouple r sat800/h/s/tr rev 2.00 (11/02/2012) 001532 description the sat800 consists of two phototransistors, each optically coupled to two light emitting diodes for ac input operation. optical coupling between the input ir led and output phototransistor allows for high isolation levels while maintaining low-level dc signal control capability. the sat800 provides an optically isolated method of controlling many interface applications such as telecommunications, industrial control and inst rumentation circuitry. the sat800 comes standard in a miniature 8 pin dip package. schematic diagram agency approvals ul/c-ul: file # e201932 vde: file # 40035191 (en 60747-5-2) applications ? registers, copiers, automatic vending machines ? system appliances, measuring instruments ? computer terminals, plcs ? telecommunication equipment, telephones ? home appliances ? digital logic inputs ? microprocessor inputs ? switching power supplies absolute maximum ratings the values indicated are absolute stress ratings. functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. exposure to absolute maximum ratings may cause permanent damage to the device and may adversely affect reliability. storage temperature ??????????..-55 to +125c operating temperature ?????????-40 to +100c continuous input current ????????????..50ma transient input current ???????.?????..500ma reverse input control voltage ????..???????6v input power dissipation 1 ????????????40mw total power dissipation 1 ???????????..300mw solder temperature ? wave (10sec)??????.?.260c solder temperature ? ir reflow (10sec)?.????..260c notes 1. power dissipation per channel ordering information part number description sat800 8 pin dip, (50/tube) sat800-h 0.40? ( 10.16mm ) lead spacing ( vde0884 ) sat800-s 8 pin smd, (50/tube) sat800-str 8 pin smd, tape and reel (1000/reel) features ? v ceo = 60v ? small 8 pin dip/smd package ? low input power consumption ? high stability ? ctr range 20 ? 300% ? high isolation voltage (5000v rms ) ? long life / high reliability ? rohs / pb-free / reach compliant note: suffixes listed above are not included in marking on device for part number identification 1 2 3 6 7 8 (+/-) input (-/+) input (+/-) input collector emitter collector sat800 4 5 (-/+) input emitter
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 2 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r parameter symbol min. typ. max. units test conditions input specifications led forward voltage v f - 1.2 1.4 v i f = 20ma terminal capacitance c t - 50 250 pf v=0, f=1khz output specifications collector-emitter voltage v ceo 60 - - v i c =10 ? a emitter-collector voltage v coe 6 - - v i e =10 ? a collector dark current i ceo - - 100 na v ce =20v floating capacitance c f - 0.6 1.0 pf v ce =0, f=1mhz cut-off frequency f c - 80 - khz v ce =5v, i c =2ma, r l =100 ??? -3db saturation voltage v ce(sat) - 0.1 0.2 v i f =20ma, i c =1ma coupled specifications rise time t r - 4.0 18.0 ? s ? i c =2ma, v cc =2v, r l =100 ? fall time t f - 3.0 18.0 ? s ? i c =2ma, v cc =2v, r l =100 ? current transfer ratio ctr 20 - 300 % i f =1ma, v ce =5v ctr classification (binning) - a 50 - 150 % i f =1ma, v ce =5v - e 20 - 300 % i f =1ma, v ce =5v isolation specifications isolation voltage v iso 5000 - - v rms rh 50%, t=1min input-output resistance r i-o - 10 12 - ?? v i-o = 500v dc electrical characteristics, t a = 25c (unless otherwise specified) test circuit: response time test circuit: frequency response
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 3 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r figure 5: collector current (i c ) vs. collector-emitter voltage (v ce ) figure 6: current transfer ratio (ctr) vs. forward current (i f ) figure 2: collector power dissipation (p c ) vs. temperature (c) figure 3: collector-emitter sa turation voltage (v ce(sat) ) vs. forward current (i f ) figure 4: forward current (i f ) vs. forward voltage (v f ) figure 1: forward current (i f ) vs. temperature (c) sat800 performance & characteristics plots, t a = 25c (unless otherwise specified)
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 4 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r figure 7: relative ctr (%) vs. temperature (c) sat800 performance & characteristics plots, t a = 25c (unless otherwise specified) figure 8: collector-emitter saturation voltage (v ce(sat) ) vs. temperature (c) figure 10: response times vs. load resistance (r l ) figure 9: collector dark current (i ceo ) vs. temperature (c) figure 11: frequency response characteristics
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 5 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r process step description parameter a preheat start temperature (oc) 150oc b preheat finish temperature (oc) 180oc c preheat time (s) 90 - 120s d melting temperature (oc) 230oc e time above melting temperature (s) 30s f peak temperature, at terminal (oc) 260oc g dwell time at peak temperature (s) 10s h cool-down (oc/s) <6oc/s sat800 solder reflow temperature profile recommendations (1) infrared reflow: refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. soldering process should not exceed temperature or time limits expressed herein. su rface temperature of device package should not exceed 250oc: a b c d f e g h (2) wave solder: (3) hand solder: maximum temperature: 260oc (at terminal) maximum time: 10s pre-heating: 100 - 150oc (30 - 90s) single occurrence maximum temperature: 350oc (at tip of soldering iron) maximum time: 3s single occurrence
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 6 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r sat800 package dimensions 8 pin dip package note: all dimensions in millimeters [mm] with inches in parenthesis ()
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 7 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r sat800 package dimensions 8 pin wide lead space package (-h) note: all dimensions in millimeters [mm] with inches in parenthesis ()
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 8 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r sat800 package dimensions 8 pin smd surface mount package (-s) note: all dimensions in millimeters [mm] with inches in parenthesis ()
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 9 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r sat800 packaging specifications tape & reel specifications (t&r) note: all dimensions in millimeters [mm] with inches in parenthesis () specification symbol dimensions, mm ( inches ) tape width w 16 ? 0.3 ( 0.63 ) sprocket hole pitch p0 4 ? 0.1 ( 0.15 ) compartment location f p2 7.5 ? 0.1 ( 0.295 ) 2 ? 0.1 ( 0.079 ) compartment pitch p1 12 ? 0.1 ( 0.472 )
? 2012 solid state optronics ? san jos, ca www.ssousa.com ? +1.408.293.4600 page 10 of 10 sat800/h/s/tr rev 2.00 (11/02/2012) 001532 sat800 ac input 60v dual photo-transistor optocouple r solid state optronics (sso) makes no warranties or representations with regards to the completeness and accuracy of this docume nt. sso reserves the right to make changes to product description, specifications at any time without further notices. sso shall not assume any liability arising out of the application or use of any product or circui t described herein. neither c ircuit patent licenses nor indemnity are expressed or implied. except as specified in sso?s standard te rms & conditions, sso disclaims liability fo r consequential or other damage, and we mak e no other warranty, expressed or implied, including merchantability and fitness for particular use. disclaimer sso does not authorize use of its devices in life support applicat ions wherein failure or malfunc tion of a device may lead to p ersonal injury or death. users of sso devices in life support applications assume all risks of such use and agree to indemnify sso against any a nd all damages resulting from such use. life s upport devices are defined as devices or syst ems which, (a) are intended for surgical i mplant into the body, or (b) support or sustain life, and (c) whose failure to per form when used properly in accordance with instructions for u se can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support devic e or system, or to affect its safety or effectiveness. life support policy sat800 packaging marking sat800 yyww date code pin 1 x ctr bin code
|
